ميزة

• The general range of Xiaomi Electric Scooter 4 Pro (2nd Gen) is approx. 60 km.

Note:General range: Measured when there is no wind and at 25°C, and the scooter is fully charged to ride at a constant speed of 15km/h in the standard mode on a flat surface with a load of 75kg. The actual range will vary depending on the load, ambient temperature, wind speed, road surface, tire pressure, battery charging cycles, riding mode, and operating habits of the people, such as rapid acceleration or deceleration

• Press the power button twice to switch the riding modes. The maximum speed for walking mode is 6 km/h, for standard mode (D) is 20km/h, and for sport mode (S) is 25km/h. Do not switch the riding modes when riding the scooter.

Note:According to the regulations of different countries, the maximum speed of D and S modes may be different from the above description. The specific requirements of local laws and regulations shall prevail.

• Max. speed 25km/h (maximum speed for each mode: Pedestrian mode: 6km/h; D: 20km/h; S: 25km/h)

• Max. motor power 1000W, Rated motor power 400W

• 10" tubeless tires, Max. load 120kg

• Approx.9 hours

• Xiaomi Electric Scooter 4 Pro (2nd Gen) ×1
• Power adapter ×1
• T-share Allen Wrench ×1
• Screws ×5
• User manual
• Important information
• Specifications

• In daily use, try to avoid completely depleting the battery. Charge it as often as possible instead, to extend the battery's service life. In addition, the battery performs better when used within a normal temperature range. If used in environments with temperatures below 0‎℃, the battery life and performance will be reduced.
  Typically, if used at -20‎℃, the range may be only half or less than that of room temperature. Avoid using the scooter in environments with temperatures below 0‎℃ or above 45‎℃. Avoid storing it in environments with temperatures below -20‎℃ or above 50‎℃.
  If you do not plan to use the scooter for more than 30 days, please charge the battery to about 80% and store it in a cool, dry place. It is recommended to fully charge every 1-2 months to extend battery life.
  Note:If the battery is not charged in time, it will likely cause irreparable damage to the battery due to over-discharge. Damage caused by over-discharging due to a lack of charging for a long period will void the warranty of the battery.

• The scooter uses tubeless tires, and there will be a certain amount of pressure loss during storage and use.
  Note:Riding your scooter with low tire pressure can speed up tire wear, and even pose the risk of a puncture. It is recommended to check the tire pressure every month and keep it between 45–50 psi. Do not ride the scooter with irregular tire pressure.

• When a flashing red wrench icon appears on the control panel, it indicates that the scooter has an issue. The following ways can help you determine:
  1. When the scooter has an issue, the speedometer displays an error code;
  2. When an error occurs, the buzzer will sound in a 3-second cycle and ring 5 times every cycle.
  

• There may be the following reasons:
  1.Power adapter error: Please connect the power adapter to power but do not connect it to the scooter, and check the LED indicator of the power adapter. If it turns red or does not turn on (green is normal), then the power adapter needs to be replaced;
  2.Battery over-discharge: If the scooter has not been used for a long time and has not been charged, the battery has likely over-discharged.
  Please contact the after-sales service team if the above issues occur;
  3.Irregular temperature: If the battery temperature is too high or too low, the thermometer icon will be on. In this case, the scooter cannot be charged. Please charge the scooter after its battery temperature returns to the normal operating range.

• Lift the quick release lever lock, and pull the quick release lever outwards to pop the bottom folding hook out.

• Please make sure the scooter is turned on. Hold the brake handle, and simultaneously press and hold the accelerator and the power button for 7 seconds. When you hear a beep, the scooter has been restored to factory settings. This operation will completely delete the data stored in the scooter, please proceed with caution.
  

• Before adjusting, please make sure the scooter is turned off and not charging. When the brake is too tight or too loose, it is recommended to refer to the following methods to adjust the brake for an optimal experience.
  Tool: 14mm T-handle socket wrench (Note: the tool needs to be prepared by yourself).
  When the brake is too tight, please use the tool to turn the nut on the screw rod counterclockwise, to slightly shorten the brake cable's exposed bottom part. When the brake is too loose, please use the tool to turn the nut on the screw rod clockwise, to slightly lengthen the brake cable's exposed bottom part.

• The lithium-ion battery has reduced activity and delayed reaction in winter. To avoid irreparable damage to the battery cell caused by low temperature, BMS will enable low-temperature protection and the thermometer icon on the control panel will light up. This will result in reduced acceleration and possibly charging issues for the scooter.
  Since low-temperature weather leads to the reduced activity of the lithium-ion battery and changed tire pressure, together with the impact of wind speed and heavy clothes worn by riders, the scooter's energy consumption will accelerate and its battery life will decrease as well.